The BWB SFP Flame Photometer
Evolving Flame Photometry to fit
your specific needs
The BWB flame photometer is a game-changer in what is possible with a low temperature flame and our product development program has, since day one, been driven by our customer’s demands. We have strong mutually beneficial partnerships within many commercial and academic organisations that faced specific challenges that were addressed by a BWB Special flame photometer.
Currently we are measuring Na, K, Li, Ca, Cs and Ba and combinations of these detectors allow users to engage with BWB engineers to evolve an ideal instrument that caters to their specific needs.
A case in point is a global supplier of ultra high purity Lithium ingots who operates thermal steam electricity power facilities, and uses exotic filtration methods to extract, among other detected ions, lithium. Our hybridized Custom BWB Flame Photometer has allowed them to augment their costly and exotic ICP and AAS instrumentation with our simple to use and exceptionally powerful instrument.
Get in touch now and see how BWB can work with you to develop a BWB Special Flame Photometer specific to your needs.
Presently we have formed a Strategic Alliance with a Major Oil and Gas Company and are co-developing a hybridized FES for online assistance in an exciting break-though technology for oil and natural gas production purposes.
SPECIALLY CONFIGURED TO SUIT YOUR NEEDS
“IRS” (INTERNAL REFERENCE STANDARD) AVAILABLE
OUR NON TRADITIONAL 5TH “UNIT
OF MEASURE” ALLOWS THE TRUE INNOVATION OF UNITS TO DISPLAY
AND LINK OUTBOUND VIA OUR FP-PC COUPLING TO THE INTER OR INTRA NET
SIMULTANEOUS DETECTION AND DISPLAY OF ANY COMBINATION OF ALL 5 ATOMS OF INTEREST
COMPATIBLE WITH BWB AFHS
INTUITIVE USER INTERFACE FOR TRUE EASE OF USE
DISPLAY PROMPTS STEP BY STEP OPERATION
BUILT-IN AIR COMPRESSOR
SOLUTIONS AND LABWARE INCLUDED
DATA SHARING VIA PC LINK
OPERATOR INDEPENDENT DETERMINATION OF RESULTS
4 USER SELECTABLE UNITS OF MEASURE WITH A FIFTH OPTIONAL UNIT OF MEASURE
USER SELECTABLE DECIMAL PLACES
INTEGRATED PRINTER USES READILY AVAILABLE PAPER FROM ANY HIGH STREET OFFICE SUPPLY COMPANY
CORRECTION OF CA FOR THE INTERFERENCE FROM HIGH LEVELS
2 – 3.5ml/min
Silicone and Tygon® or as specified
Na/K/Li = <0.5% to each other when
equal in concentration at <100ppm
Required desk space for Instrument
50cm (H) x 45cm (W) x45cm (D)
For Safety reasons the Flame photometer requires 1m of unobstructed space above to allow dissipation of heat from the chimney.
SFP Flame Photometer
51cm (H) x 39cm (W) x 35cm (D)
(20in x 15in x 14in)
65cm (H) x 49cm (W) x 43cm (D)
(25in x 19in x 17in)
SFP Flame Photometer – 14kg (30.8lbs)
Shipping – 25kg (55.1lbs)
Single point calibration
Na 0.1 – 60ppm
K 0.05 – 100ppm
Li 0.05 – 50ppm
Ca 1.0 – 100ppm
Ba 5 – 100ppm
Cs 0.14 – 100ppm
Multi Point Calibration
Na 0.1 – 1000ppm
K 0.05 – 1000ppm
Li 0.05 – 1000ppm
Ca 1.0 – 1000ppm
Ba 5.0 – 3000ppm
Cs 0.5 – 1000ppm
<1% Coefficient of variability for 20 consecutive samples over ten minutes at concentrations of 100ppm or less. (After instrument stabilisation).
Limit of detection (LOD) and
limit of quantification (LOQ) displayed
Na – 0.03ppm Na – 0.1ppm
K – 0.02ppm K – 0.05ppm
Li – 0.02ppm Li – 0.05ppm
Ca – 0.3ppm Ca – 1ppm
Ba – 1.6ppm Ba – 5.0ppm
Cs – 0.041ppm Cs – 0.14ppm
Customisable measurement of Na, K, Li, Ca,
Ba and Cs
0-2.5 volt output (based on sample concentration linked to element of users choice)
Optional 4-20mA output in place of the above
Optional integrated printer
.CSV and .PDF generated reports and files via FP-PC software
Optional collection cup to provide live readings
Recommended minimum warm up
time based on ambient temperature
21°C – 25 minutes
100V – 250V AC at 50 or 60Hz
Propane, Butane or Natural Gas*
regulated to 19Bar. Flow rate of 0.4l/min
*with modifications. BWB Technologies recommends either Propane or Butane for optimum results.
LCD, four line, alpha numeric, back lit.
Left hand or right hand chimney configuration.
Customized calibration curves for any or all of the atoms of interest.
Customized calibration solutions for multiple points (up to 14) for both in factory pre-shipment calibration and after sales supply.
User selectable units of measure including client determined unique units of measure.
WHAT’S IN THE BOX
PC Leads USB and RS232
Power lead to suit your region
Manuals covering all aspects
of the FP
Quick Start guides
Warranty Registration Form
Certificates of analysis for all provided Fluids
Material Safety Data Sheets for all provided Fluids
The FP-PC Software installation USB
150ml of BWB recommended cleaning solution
Customisable calibration fluids based upon your needs.
100ml conical flask with screw lid
100 disposable sample cups
1L of De-Ionised water
2m of waste tube
Set of spare fuses
10 x 10ml pipettes
10 x 1ml pipettes